Настройки на Mgcamd
В newcamd.list на Mgcamd 1.35 съм сложил настройка на :
CWS_KEEPALIVE = 300 CWS_INCOMING_PORT = 12000 CWS = 84.16.ххх.ххх 3001 user pass 0102030405060708091011121314, но не се отваря нищо. Трябва ли да се направят други задължителни настройки - в рутера портове, или нещо друго специфично в емулатора, за да се отключат програмите? С IPbox900 съм, мрежата е през рутер Linksys 54GL с DDWRT. Моля, ако някой се чувства компетентен да сподели. Благодаря! |
При мен е така ама съм с дрийймбокс и си баца.
CWS = XXX.XXX.XXX.XXX port user pass 0102030405060708091011121314 |
Цитирай:
|
С кой имидж си на ипбокса?
Постни си mg_cfg, приорити, игнор листите и кажи кой оператор търсиш. |
Абе, аз на всяка манджа мерудия, ама на дескея не се ли скага интервали между 01 02 ... 14?
CWS = ********** 11011 bobikat bobikat 01 02 03 04 05 06 07 08 09 10 11 12 13 14 lan newcs |
не трябва нищо допълнително, дори тези CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 12000 са излишни може би трябва да се настрои ръчно box type ако го пуснеш ръчно в конзола с пуснато логване там, може да видиш причината да не отваря нищо |
Цитирай:
наскоро пращах на някой примери и току-виж решил че интервалите са ненужни :hammer: |
Цитирай:
Това е mg_cfg, пипал съм само настройките за лога (L: { 01 } 192.168.1.100 514), но не мога да го извадя на компютъра през Kiwi Syslog Daemon: # EMM messages # 00 don't show any EMMs (default) # 01 show only valid EMMs # 02 show valid and bad EMMs with complete data display M: { 01 } # ECM messages # 00 don't show anything about ecm # 01 normal mode, show pids processed, decoded ecm and cw # 02 verbose mode, show valid and bad ECMs with data C: { 01 } # AU # 00 disable, no emm pids processed # 01 enable, emm pids always processed for soft-au and shared cards # 02 auto, emm started only if channel cant be decoded # 03 process emm pids for network cards update only A: { 02 } # key update (sum 01 or 02 with 04) # 01 update only new keys, default setting # 02 update all keys (used for valid PMK checking) # 04 enable TPS au # + tps SID, which pmt pid contains au pid U: { 01 } 0x12c0 # config files folder (softcam, autoroll, ignore/priority) # 00 files in /var/keys # 01 files in /tmp T: { 00 } # network mode, use summ for several clients # 00 no network (default) # 01 newcamd netclient # 02 radegast netclient # 04 camd3 netclient # 08 gbox netclient # 32 cccamd netclient, card list saved as /tmp/cccamd.info # (ECM only, supported server version up to 2.1.1, later not work) G: { 32 } # network retry, use summ for several options # 00 disable # 01 retry every new ecm # 02 try to connect to offline shares every Q: seconds # 04 try to detect and fast reconnect to lost (and not used atm) server # + XX messages number and YY seconds to reconnect # mg will reconnect to server, if no answer to last XX ecm/keepalive or # if no answer for last ecm or keepalive sent for YY seconds # set to 0 to disable N: { 07 } 5 30 # network ecm timeout in seconds K: { 05 } # newcamd dead routes connect retry, sec Q: { 600 } # network shares priority # 00 gbox, newcamd, cccamd, radegast, camd3 (default) # 01 camd3, radegast, cccamd, gbox, newcamd # 02 cccamd, newcamd, camd3, gbox, radegast P: { 00 } # on screen display type # 00 No OSD (default) # 01 neutrino # 02 enigma # 03 relook # + user password for http auth O: { 00 } username password # on screen display Options, summ of: # 01 show emu ecm # 02 show network shares messages # 04 show decoding failed / fta # 08 show emm keys update # + web port to use for osd S: { 03 } 80 # Log option, summ of: # 00 off # 01 network udp log # 02 log to console # 04 file, appended ! delete it by yourself, before it eat all your hdd # + IP udp-port log-file-name L: { 01 } 192.168.1.100 514 # keep ecm cache, seconds # every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory, # for openbox/elanvision users with remote shares make sense to set it higher than default value, # to not hammer cards while timeshifting or playing crypted recordings. E: { 15 } # cache option, summ of: # 00 Off (default) # 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list # 02 Ecm data cache, remember CW for (E:) time # 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart H: { 07 } # reread files, summ of: # 00 No (default) # 01 reread config file on channel change (including priority and ignore, but not replace/cache) # 02 reread SoftCam.Key on channel change # 04 reread SoftCam.Key if file changed R: { 00 } # debug, summ of # 00 off (default) # 01 debug ecm # 02 debug emm # 04 debug network ecm # 08 debug network emm # 16 debug network login # 32 show mem/cpu stats every 1 min # 64 add timestamp to log messages D: { 00 } # box type # 00 autodetect, change only if you think wrong type detected. # 01 dbox2 # 02 dreambox # 03 triple-dragon # 04 relook # 05 openbox # 06 dreambox/mips # 08 stapi/kathrein # 09 stapi/ipbox # 11 stapi/openbox B: { 09 } # map all 180x nagra caids to 1801 # default is 01 F: { 01 } |
Промени редовете:
Код:
G: { 33 } |
ако линията която ти дават е нюкамд(N) това трябва да е G: { 01 }
за да видиш лога - L: { 02 } без ип адрес, телнетваш до бокса и /var/bin/mgcamd и натискаш ентер и гледаш(може да трябва да промениш нещо ако пътя или файла са с други имена) |
Всички времена са във формат GMT +3. Часът е 06:19. |
DTV-BG Powered by vBulletin Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.