Инструкция за инсталиране на Enigma 2 софтуер !
Тази важна тема ще посветя като обесня как се инсталира, софтуер Enigma 2 SIfteam на IPBOX 900/910/9000.
Държа да отбележа, че при инсталирането на този софтуер се изисква работа през Hyperterminal/Putty ! Общо взето процеса е еднакъв и при трите модела на приемниците. Сваляте софтуера от тук: Enigma2 flash SifTeam ipbox900HD http://rapidshare.com/files/172447998/u ... _900hd.rar Enigma2 flash SifTeam ipbox910HD http://rapidshare.com/files/172449964/u ... _910hd.rar Enigma2 flash SifTeam ipbox9000HD http://rapidshare.com/files/172455437/u ... 9000hd.rar Разархивирате архива, след което променяте името на файла на usb_update.img. Поставяте този файл в USB Flash-ка (флашката трябва да е форматирана под FAT32 и да е празна) Слагате флашката на USB на IPBOX приемника на задния панел. Изключвате приемника (Shut Down, а не Stand By). Включвате приемника, след което задържате POWER бутона продължително време, след което го пускате. На дисплей-а на приемника ще ви изпише как точно преминава процеса (Erasing 01,02... и т.н). Тук е важно да спомена, че ако по време на този процес ви даде Error (грешка и ви се изпише на дисплей-а, е нужно просто да изключите приемника и да започнете обновяването на софтуера наново, това се случва изключително рядко като процес). След като Enigma 2 софтуера е вече инсталиран, ще ви е нужен NULLMODEM (RS 232) кабел и компютър с COM PORT. Вързвате приемника към компютъра през COM порта. Отваряте hiperterminal (има го във всеки Windows, инсталира се през Control Panel), или ползвайте Putty, където се избира Serial Connection. Посочва се 11152 (скорост на предаване на данните). След което е нужно приемника да се включи от Power бутона и в същият момент на неговото пускане на програмата (Hiperterminal или Putty) се задържа - CRTL+Z (или се натиска няколко пъти), докато приемника влезе в CONSOLE режим. На програмата обикновенно се изписва - cuberevo> където се въвежда следната команда: Код:
setenv bootargs console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 rootfstype=jffs2 rw bigphysarea=10240 ip=192.168.1.150:192.168.1.111:192.168.1.1:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 192.168.1.111 сървър на приемника (тази опция не е важна и може да я оставите така) 192.168.1.1 IP-то на вашият Gateway (Рутер) 255.255.255.0 Нетмаска (променя се само последната цифра) След това се въвежда команда - Код:
saveenv Това е първата Enigma 2 от Sifteam 0.1.0 (Beta) ! |
Re: Инструкция за инсталиране на Enigma 2 софтуер !
Цитирай:
|
Дам странно е, че иска flash-ката да е прясно форматирана. И на НЛБ софт пак се случва това
|
Хора, зарежете ги тези флашки. Винаги, когато съм опитвал да инсталирам от флаш памет съм имал проблем. Ползвам си FlashTools с USB кабел към лаптопа и никога досега не ме е подвел.
|
E2 on USB / HDD Definitive Installation Guide
E2 on USB / HDD Definitive Installation Guide
PREPARATIONS: Requirements: UBOOT 1.3.1 (IO firmware installed) FLASHFXP utility to connect to Set-top box via FTP PUTTY – for telnet & serial connec****ty Serial NULL Modem cable – (9-pin to 9-pin Female -2– Female cable) £1-£2 @ebay Laptop - with one Serial COM port. (The COM Port must be configured to 115200 Bits per second in Device Manager & in PUTTY) My preference is to use PC & Laptop with Windws XP or Windows 2000 – because I do not like Windows VISTA – because you always have to select to allow software to run when you are trying to do something. Step #A A) To begin with – you must have UBOOT 1.3.1 or later, installed in your box: All recent images are 1.3.1 or better. Review this post (link below) – depending on whether you have Revo, Mini or NewMini: http://www.sat-universe.com/showthread.php?t=94016 Use the flash image that is relevant to your box found in the ZIP file provided by the more senior SU member K@lkov. E.g. If you have the 900HD – use that IMG-file (usb_config.welcome900.img). & 910HD & 9000HD, etc. I found that only these multi-boot images worked for me. Copy the IMG file, eg. “usb_config.welcome9000.img” to the \tmp - folder in the Cuberevo via FTP. I always use FLASHFXP tool to do this – you and use whichever ftp tool that tickles your fancy. NB: I strongly recommend that NLB base image (9207 or Later – I used 9580) be used – however Sifteam or DGS can obviously work as well. For NLB image – I simply connect to Web interface from my PC and do a FIRMWARE update. This function will automatically apply the IMG file that is in the TMP folder. Not all firmware updates are supported via WEB interface in this manner but this little update is supported like this. “Done”- will be displayed in LCD display of receiver – simply re-start / reboot the receiver. AFTER CUBEREVO is restarted -- continue to Step #2 Step #B B) ( Instructions taken from BADEYEAH ) Except that I use EXT2 linux format instead of EXT3 which is slower. Depending on which image you use – you will need to authenticate in FLASHFXP each time you connect to the set-top box. The NLB settings for authentication are: USER: root PW’D: relook NB: If you do not have ESATA or SATA HDD then usb will be “sda1” or sda1 & sda2 if yore usb has two partitions. ++++++++++++++++++++++++++++++++++++++++++ 1. Boot your NLB / Sifteam / DGS image, wait to full boot. 2. Insert your USB stick 3. Telnet to your box, execute mount 4. In the list check - if the /dev/sdb1 is mounted (if is FAT probably is mounted to /mnt/usb/usb0) 5. umount it - umount /mnt/usb/usb0 6. now execute fdisk /dev/sdb (not sdb1) 7. on the prompt press p - to see current partition table 8. press d - to delete partitions, if it is only one proceed, if not - press d again and delete all partitons 9. press p again - there will be no partitons now 10. Press n - to create new partition 11. select p - primary 12. select 1 13. press enter, enter 14. press w to write changes & exit 15. You have just created linux partition on your usb stick 16. Now format this partition - mkfs.ext2 /dev/sdb1 17. mount formatted partition again - mount -t ext2 /dev/sdb1 /mnt/usb/usb0 18. Now ftp e2.tar.gz to /mnt/usb/usb0 (I used FLASHFXP to do this) 19. execute cd /mnt/usb/usb0 20. execute tar -zxvf e2.tar.gz, wait few minutes to decompress all. (wait for prompt) 21. after decompress type, sync to unmount just cd / umount /dev/sdb1 ++++++++++++++++++++++++++++++++++++++++++++++++++++ Switch OFF IPbox and make sure that you proceed as follows: Leave USB in the box, connect serial cable from laptop to CubeRevo / Mini or NewMini and start your Laptop. Run PUTTY and configure SERIAL COM connection with speed of 115200. You can call this connection REVO while you are at it for future CONSOLE debugging and click on SAVE within PUTTY. Console connection is DIRECT and does not require authentication. Step #C C) Ensure that IP Box is switched off & the E2 image installed on USB single EXT2 partition (I used 2Gb stick) – leave USB stick connected (no need to remove USB after UMOUNT command). Connect serial cable between Laptop / PC and SET TOP box and run PUTTY as specified above. Blank Black screen will open with one green cursor blinking. Hold down CTRL + Z on your keyboard with one hand while you switch on the IPBox with the other hand. Wait until you see that CONSOLE appears on LCD display of Ipbox. The Putty screen will change to “Cuberevo>” or “cuberevo-mini>” prompt very quickly. NEXT Be very careful how you do the next tasks because these are the most important to succeed in getting this setup to work – do not worry tho – it will all work fine. Copy and paste the following without any space at the start and end of Text selection then press ENTER in PUTTY console window – remember to change sdb1 to sda1 depending on if you have HDD or not -> Copy and paste after *line below: setenv menu_1 'setenv bootargs "console=ttyAS1,115200 panic=3 root=/dev/mtdblock3 bigphysarea=1500";setenv bootcmd "bootm a0060000";save;boot' PRESS ENTER in CONSOLE - you may get an error message saying “’setenv’ is not recognised command. Simply ignore this and re-paste the same text again and press ENTER again. This second time – there is no error message. Next copy and paste again after * line below: setenv menu_2 'setenv ipaddr 192.168.1.9;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootide "run bootargside;ide reset;ext2load ide 0:2 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 panic=3 bigphysarea=10240 root=/dev/sda2 rw rootfstype=ext2 init=/bin/devinit ip=$ipaddr::$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "run bootide";save;boot' PRESS ENTER in CONSOLE again and everything will be fine – no error message. Next copy and paste again after * line below: setenv menu_3 'setenv ipaddr 192.168.1.9;setenv gateway 192.168.1.1;setenv netmask 255.255.255.0;setenv bootusb "run bootargsusb;usb reset;ext2load usb 0:1 a5ff0000 boot/uImage;bootm a5ff0000";setenv bootargside "setenv bootargs console=ttyAS1,115200 panic=3 bigphysarea=10240 root=/dev/sda2 rw rootfstype=ext2 init=/bin/devinit ip=$ipaddr::$gateway:$netmask mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000";setenv bootcmd "run bootusb";save;boot' PRESS ENTER in CONSOLE again and everything will be fine – no error message Type “saveenv” without quotes “” in console and press ENTER. – you will see a screen similar to below: cuberevo-mini> saveenv Saving Environment to Flash... Un-Protected 1 sectors Erasing Flash... . Erased 1 sectors Writing to Flash... done Protected 1 sectors -**** Now are done. Simply restart your box using On / Off switch and press 3 to start from USB with HDD or 1 to start from Original DGS / NLB / SIF flash image. You can add more menu items or change numbering as you need - so long as you understand the STARTUP parameters. |
@CANALSAT
18. Now ftp e2.tar.gz to /mnt/usb/usb0 (I used FLASHFXP to do this) 19. execute cd /mnt/usb/usb0 20. execute tar -zxvf e2.tar.gz, wait few minutes to decompress all. (wait for prompt) 21. after decompress type, sync Само това е достатъчно за инсталиране на е2 на USB флашка! Всичко останало е прекалено сложно и ненужно. Естествено преди това се инсталира мултибоот върху DGstation базирания имидж. |
Цитирай:
Класическия fdisk -Който е стандартния туул за разделяне,триене на партишъни. mkfs -за създаване на партишъни Не мисля че нещо допълнително би навредил на някой ;) |
Марто е напълно прав. Е2 се инсталира на HDD или флашка точно с тези команди при инсталиран предварително мултибут имидж, а всичко останало е объркващо и излишно. И целия процес трае не повече от 5 минути.
Пък нека после "феновете" на IpBox-а да си плямпат колко сложно и трудно било ;;573 |
На фенките им е трудно,пък и не обичат да се возят на Боинг!
|
Пробвах да инсталирам енигма 2 на usb флашката но имам само /mnt/usb липсва usb0.Инсталирал съм сифтийм 9580 и мултибут имидж.Някакви идеий.
|
Всички времена са във формат GMT +3. Часът е 19:49. |
DTV-BG Powered by vBulletin Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.