Ъпдейт на бутлоудър
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000007
WC1=FFFFFFE8
RC2=00000019
WC2=00000035
RC3=00000010
WC3=FFFFFFE8
RC4=00000010
WC4=00000035
NWC=0000000E
RC5=00000007
WC5=0000000E
RC6=00000019
WC6=0000000E
NRC=00000010
RW=00000013
WW=0000004E
G=00000000 R=00000010 W=0000000E
BL=00000000
RC1=00000001
RC2=00000017
BL=00000001
RC1=00000005
RC2=00000019
BL=00000002
RC1=00000006
RC2=00000016
BL=00000003
RC1=0000000A
RC2=00000019
BL=00000004
RC1=00000005
RC2=00000019
BL=00000005
RC1=00000006
RC2=0000001A
BL=00000006
RC1=00000003
RC2=00000018
BL=00000007
RC1=00000005
RC2=00000019
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Sat Dec 10 11:22:02 WEST 2011 (Administrator@buildserver)
Copyright (C) Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 08 Vendor 125F Product 102E: Mass-Storage Device
USBMASS: Unit 0 connected
found image:
flashing...
Reading usbdisk0:et6x00/cfe.bin: Done. 316012 bytes read
Programming...
offset=0 copysize=316012
done. 316012 bytes written
flashing...
Reading usbdisk0:et6x00/splash.bin: Done. 1244214 bytes read
Programming...
offset=0 copysize=1244214
done. 1244214 bytes written
bootloader updated!
след рестарта
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000007
WC1=FFFFFFEA
RC2=00000019
WC2=00000035
RC3=00000010
WC3=FFFFFFEA
RC4=00000010
WC4=00000036
NWC=00000010
RC5=00000007
WC5=00000010
RC6=00000019
WC6=00000010
NRC=00000010
RW=00000013
WW=0000004D
G=00000000 R=00000010 W=00000010
BL=00000000
RC1=00000001
RC2=00000017
BL=00000001
RC1=00000005
RC2=00000019
BL=00000002
RC1=00000006
RC2=00000016
BL=00000003
RC1=0000000A
RC2=00000019
BL=00000004
RC1=00000005
RC2=00000019
BL=00000005
RC1=00000006
RC2=00000019
BL=00000006
RC1=00000003
RC2=00000018
BL=00000007
RC1=00000005
RC2=00000019
SCfC3
COPY CODE
COMPARE CODE
4567
BCM97413B1 CFE v2.26, CFE core v2.12, Endian Mode: Little
Build Date: Thu Sep 29 21:44:42 WEDT 2011 (Administrator@buildserver)
Copyright (C) Broadcom Corporation.
start cfe init device
sec-0 nblks=8 blksiz=8192
sec-1 nblks=63 blksiz=65536
Enabling NAND flash at CS1, NOR flash at CS0
NAND Flash size = 128MB
CPU speed: 405MHz
Memory Config: 64-bit UMA
Device Tech: 1Gb
Total memory: 512MB
Boot Device: NOR
Total flash: 4MB
Initializing USB.
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
USB: Locating Class 09 Vendor 0000 Product 0000: USB Hub
CFE initialized.
Set default GPIO...
USB: New device connected to bus 1 hub 1 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 09 Vendor 1A40 Product 0101: USB Hub
USB: New device connected to bus 1 hub 2 port 1
USB: Resetting device on bus 1 port 1
USB: Locating Class 08 Vendor 125F Product 102E: Mass-Storage Device
USBMASS: Unit 0 connected
found image:
Bootloader ET6X00
flash image? (OK/CANCEL)
found image:
Bootloader ET6X00
flash image? (OK/CANCEL)
found image:
Bootloader ET6X00
flash image? (OK/CANCEL)
booting...
Starting splash screen.
***************************************************
Found splash image - Width = 720 Height = 576
bmp ptr : 0x8fa00000 , surface ptr : 0xafc00000
***************************************************
Loader:elf Filesys:raw Dev:nandflash0.kernel File: Options
null)
Loading: !!!!! UNC read error occurred, while reading from NAND flash -1
0x80001000/7283232 0x806f3220/131760 Entry address is 0x805705b0
TP1 Entry Address at 0x80000ffc = 805705b0
Starting program at 0x805705b0